or Login >>         

Search C4 - DS4 Owners

Search For:   Enhanced Query Form
Search type: Basic  Advanced

Results 2241 - 2260 of 9585 in Forum

bullet As part of thread: Type 'C' Screen Help
Can you explain what you are refering to when you say "unit"? a control ECU? Stereo? Screen?...??? The screens are interchangable and a simple ex...
Posted by Rich_Eason on 18 June 2013 | Relevance: 0.6

bullet As part of thread: Two Dealers, Very Different Opinions, Someone is not telling the truth!
... A number C4 Owners - myself included - have switched to the Philips SilverVision globes. General consensus is that they flash a brighter orange ...
Posted by CamM on 12 May 2012 | Relevance: 0.6

bullet As part of thread: Turning the ICE Off
It might be a case of pressing the on/off switch and holding it down for a few seconds?
Posted by Gadgie on 02 August 2014 | Relevance: 0.6

bullet As part of thread: Turn ECO off for good?
...less than the wear and tear on the finger used to switch it off at each restart. I've no problem at all with ECO S&S, the set up is very cons...
Posted by Richard_C on 11 September 2023 | Relevance: 0.6

bullet As part of thread: Turn ECO off for good?

Posted by StuBeeDoo on 12 September 2023 | Relevance: 0.6

bullet As part of thread: Turbo seized advice
If you have a turbo, driven by the exhaust gases, it will continue to spin when the engine is switched off, if running at the time. When the engine s...
Posted by wunny on 30 June 2018 | Relevance: 0.6

bullet As part of thread: Turbo copy position fault
It's unlikely to be anythig to to with the turbo itself, faulty turbo actuator control solenoid?? Tom
Posted by tomandjo2 on 07 September 2021 | Relevance: 0.6

bullet As part of thread: Turbo Whistle
...o. Remember good turbo manners.... have a hard run, let it cool down a bit before switch off... and keep on top of regular oil changes.
Posted by Phil on 25 August 2010 | Relevance: 0.6

bullet As part of thread: Turbo Replacement Problem Fault P2562
Don't know if this helps or not: P2562 Turbocharger position copy signal : Positive loop gap Check for turbo control vacuum supply, possibly t...
Posted by BigJohnD on 06 January 2012 | Relevance: 0.6

bullet As part of thread: Turbo Not Whistling
...e vacuum - which is what controls the boost actuator. I'm not saying it's that - they're could be plenty of other things out there it could be.
Posted by Biohead on 16 July 2016 | Relevance: 0.6

bullet As part of thread: Turbo Issue - but not during engine regen?
...of these are a symptom and not a cause of the ECU controlling these components in this manner. When doing a regen, your engine is working more in-effi...
Posted by nitropixie on 29 January 2016 | Relevance: 0.6

bullet As part of thread: Turbo Failure Prevention
...s hot, don't just whizz into the service area and switch off. Wait a couple of minutes, no revving, before switching off. This will take some of the...
Posted by BigJohnD on 01 February 2012 | Relevance: 0.6

bullet As part of thread: Turbo Cooooooo
... As a diesel usually has no throttle body it just controls the amount of fuel injected you have non of those issues and thus non of the cool noises ei...
Posted by wozza on 30 April 2012 | Relevance: 0.6

bullet As part of thread: Turbo Cartridge CHRA
Today I brought the engine to warmth temperature and added the engine flush fluid and left the engine to idle for about 10 minutes before switching it...
Posted by manon218 on 14 June 2015 | Relevance: 0.6

bullet As part of thread: Turbo
...ugins/forum/forum_viewtopic.php?97127 or pressure switch. Check the turbo heat shield as it's common for a securing lug to break and the heat shi...
Posted by Dave_Retired. on 28 December 2013 | Relevance: 0.6

bullet As part of thread: Tuning box or remap.. ??
...thout. Tuning box disadvantages: Cannot control boost pressures of the Turbo (the cars ECU will be doing overtime to correct it). Just ...
Posted by Biohead on 03 March 2011 | Relevance: 0.6

bullet As part of thread: Trying to find part number for micro switch
...ld be able to see which one you have if you have removed the switch. {e_PLUGIN}forum/attachment/34563/1435855575_34563_FT208604_switch_.jpg
Posted by AndrewM on 02 July 2015 | Relevance: 0.6

bullet As part of thread: Trying the patience of a saint ESP / ABS / Brake faults after replacing rear caliper & speed sensor
really really really daft one... also looking around i have stumbled across the foot brake switch causing C4 chaos.... doe it really throw out AB...
Posted by gt4thug on 03 November 2020 | Relevance: 0.6

bullet As part of thread: Trying the patience of a saint ESP / ABS / Brake faults after replacing rear caliper & speed sensor
... a poor battery this is where computers and switchgear working tolerances become a problem to diagnose and its easier to ask people who have had...
Posted by gt4thug on 09 November 2020 | Relevance: 0.6

bullet As part of thread: Trouble Code P0075 - Updated correct error code.
...s poor connection or corroded terminals Faulty control solenoid Short to power Short to ground Faulty ECM Read more at: http://www.ob...
Posted by thinush on 26 October 2015 | Relevance: 0.6

Go to page   <<        >>