Hi TMD63, if you are going to make any sense of your readings, you need the specification power/torque curves which also show the controlled boost set... Posted by gmerry on 05 April 2016 | Relevance: 0.6
...inor emissions aberrations. Some can be cured by switching on the ignition and waiting until the pre-flight checks are complete, about 30 seconds.
... Posted by BigJohnD on 09 May 2018 | Relevance: 0.6
... after driving for 5 mins but again, as soon as I switched it from blowing on the window to the front vents, it went off again. The trip computer read... Posted by WoodyGrandPicasso on 02 March 2015 | Relevance: 0.6
...'t turn freely.
When it doesn't work, leave the switch on, try removing the cover above the pedals and give the bottom of the blower a sharp tap wit... Posted by Joker on 02 March 2015 | Relevance: 0.6
Lots of issues there but most of them minor and quite common.
For the windows it may be the switch. Try spraying with a switch cleaner such as Se... Posted by PPP7 on 23 October 2010 | Relevance: 0.6
...M hardware service eng!
All I need for the cleaning bit is to get at the switches, but I need to get the panel off? Any ideas folks please? Posted by Jonzjob on 19 August 2012 | Relevance: 0.6
Sorry, I don't know how the panel comes off. The thing about the contact spray is if you squirt it around a switch (still attached) it often works. Posted by FakeConcern on 19 August 2012 | Relevance: 0.6
...nded to the control panel. I'll stop short of calling it fixed until I've been on the regular 100 mile journey it gets used for at the weekend. Posted by jloyd on 02 July 2018 | Relevance: 0.6
...ressor isn't staying on, that's not too helpful. it could be a faulty compressor, faulty pressure switch or low on gas.
Try another garage. Posted by rusky on 04 July 2018 | Relevance: 0.6
check voltages at the 4 pin connector, as that is what controls the fan
here's what i did....... find a good earth, i use the dpf shield and wedg... Posted by peterjb44 on 16 July 2018 | Relevance: 0.6
...s/20180716_125204_zpsylydsvak.jpg
....................................................fan..........2 speed control unit.........engine ecu
Posted by peterjb44 on 16 July 2018 | Relevance: 0.6
...ltage on the big 2 pin connector (CP088) going in to the fan control unit. I'll check the voltages this afternoon on the 2 pin and 4 pin plugs. Posted by jloyd on 16 July 2018 | Relevance: 0.6
All sorted now. Thanks for the help. I wasn't getting 12v on the connector that goes in to the fan controller, followed the blue wire to the fusebox o... Posted by jloyd on 16 July 2018 | Relevance: 0.6
Hers's one post on the issue http://c4owners.org/plugins/forum/forum_viewtopic.php?183477.0#post_183479 however the microswitch is a problem area due ... Posted by Dave_Retired. on 15 January 2014 | Relevance: 0.6
I purchased a new switch from my local Citroen deal as a decent price and went about fitting on Sunday. However I was shocked to find that the tailga... Posted by Bodger70 on 21 January 2014 | Relevance: 0.6
... lights and the service light came on and a speed control failure warning popped up on the display. It was fine when we drove off and has not appeared... Posted by on 09 April 2010 | Relevance: 0.6
...on a tiny idle until it warms up and then have to switch off and re-start.
AA Man says it was flooded.
Citroen main dealer says no fault sho... Posted by on 05 December 2010 | Relevance: 0.6
...press the start button, it starts, other times it switches off. The next time it does what it should.
So, yes there is a fault and I believe tha... Posted by wunny on 26 June 2020 | Relevance: 0.6
As said above, if your parked on a slope you some times get the warning. I just think the sensor/switch is a bit on the sensitive side Posted by Ham on 05 July 2011 | Relevance: 0.6
As part of thread: Intermittent lack of power and strange readings from OBDII
With Graphics from: Dave Forum Icons by Axialis Emotes by Seb