It is a limit, to stop you goosing the engine.
It also helps that if you knock it into neutral with cruise on it doesn’t blow the engine. Posted by FrankBullitt on 19 June 2021 | Relevance: 0.6
...circuit high input.
Code P1158 = Lack of HO2S22 switch - sensor indicates rich.
Code P1161 = TPS coherence.
Lights on dash were:
Red Park B... Posted by Munro on 17 February 2021 | Relevance: 0.6
New battery hasn't fixed it unfortunately, although I think the old one wasn't great. I can now switch the radio on without the engine running.
I... Posted by jloyd on 19 September 2019 | Relevance: 0.6
...t effects the rear wiper - it works fine from the control stalk, but also has a mind of its own because it starts going whenever the rear hatch is ope... Posted by cornwalldream on 13 October 2012 | Relevance: 0.6
...s which were operated as required by a press-down switch, so were only on when the button was down. This was used to start on cold mornings, but never... Posted by routemaster1 on 08 September 2015 | Relevance: 0.6
...cold the plugs can run for several minutes before switching off. Once off they do NOT continue to glow.
To sum up; they can run for a couple of sec... Posted by COLVERT on 08 September 2015 | Relevance: 0.6
...an:
All functions in a modern engine are controlled by the ECM communicating with an elaborate set of sensors measuring everything from R.P.M... Posted by tmd63 on 09 September 2015 | Relevance: 0.6
...oses, the only thing I have to work out is how to get the steering wheeling controls to work. As for the sat nav, I use my phone with co-pilot. Posted by maniacs_id_vaunted on 20 February 2016 | Relevance: 0.6
The BSI is the main ECU.It is a central controller or interconnection unit that allows the sharing and management of information across the multiple E... Posted by rusky on 26 August 2016 | Relevance: 0.6
...well, you might be able to use the steering wheel controls to put the parrot in pairing mode. In this case you don't need the pilot.
See the "par... Posted by on 28 July 2012 | Relevance: 0.6
Wondered if anyone could tell me why I get a message telling me 'your remote control battery is flat' every time I start the car.
Have you put... Posted by BigJohnD on 08 December 2011 | Relevance: 0.6
...t.
Suspect now:
1 - crankssensor - it control the timing og ignition.
2 - high pressure pump and some error in the HP or LP circuit, or ... Posted by Farmerguy on 02 November 2025 | Relevance: 0.6
Try lowering all windows then press and hold the lock button on your remote control, all windows should close!
See if that makes a difference, it's ... Posted by KenC on 19 July 2017 | Relevance: 0.6
If the boot is open and you press the switch you should not hear anything apart from the click of the microswitch I would have thought?
Does your... Posted by PPP7 on 22 August 2012 | Relevance: 0.6
If the boot is open and you press the switch you should not hear anything apart from the click of the microswitch I would have thought?
Does y... Posted by elsieyam on 23 August 2012 | Relevance: 0.6
...posted in another topic I had found for the turbo control solenoid but the part number posted didn't bring any results on citroen service box when I p... Posted by ham_vts on 26 February 2015 | Relevance: 0.6
All back together again, took about 45 minutes to refit the turbo position sensor & whilst doing so I found the turbo control solenoid you mention... Posted by ham_vts on 26 February 2015 | Relevance: 0.6
...
What is the rest position for the two vacuum controlled valves on the inlet manifold?
Mine are currently top valve open, lower vale closed. ... Posted by ham_vts on 12 October 2015 | Relevance: 0.6
No Cam your correct, it is sealed for life but.............
They do benefit from an oil change.
However it could be the actual control unit ... Posted by Dave_Retired. on 08 July 2012 | Relevance: 0.6
As part of thread: 1.6 blueHdi - rev limit 2500 rpm in neutral, no fault codes in Diagbox
With Graphics from: Dave Forum Icons by Axialis Emotes by Seb