...rning lights at all nor illuminated lights on any switches.
Our usual garage has offered to do a computer diagnostic check for me but would that... Posted by belfix on 01 August 2013 | Relevance: 0.6
... gone down 2 marks. Reversing lights were not on. Switched engine off, waited a couple of seconds, started up and guess what? NO alarm. Curious? Posted by belfix on 05 August 2013 | Relevance: 0.6
...elivery by Citroen main dealer and as thus do not switch off over a certain speed. Found a red diode attached to gear lever housing with wire in and w... Posted by belfix on 12 November 2013 | Relevance: 0.6
...ount third light) is still lighting brightly when switched to park lights. No difference when brake pedal is applied.
Cant rotate the bulbs as t... Posted by mduque on 20 August 2015 | Relevance: 0.6
Update fellas. After moving and twist the LED bulbs, I still have not managed to make it work as it should. At daytime when park-lights switched-off, ... Posted by mduque on 21 August 2015 | Relevance: 0.6
I had similar on mine in the past.
Replaced strut top mounts, drop links and lower control arms fixed it for me.
The control arms was the most ... Posted by danlat1415 on 05 July 2023 | Relevance: 0.6
...Full auto boxes are fine, it's the electronically controlled manual gearboxes (EGS) which have gear change issues and you're confusing the two which a... Posted by Dave_Retired. on 09 July 2013 | Relevance: 0.6
...Peugeot, Ford, Volvo, BMW and Mazda.
It will cruise all day at 130km/h because the French demand it. It is powerful and economical, and it's long... Posted by BigJohnD on 05 May 2010 | Relevance: 0.6
...cant have the top one now as it wont accept stalk control.
This one below does, but im trying the dealer to see if anything is now available. local ... Posted by Ham on 12 July 2007 | Relevance: 0.6
...re rather loud. I've also still got all the wheel controls working (see SatNav thread).
I'm going to ask my dealer what parts they fitted to reta... Posted by on 21 July 2007 | Relevance: 0.6
...uld make reverse sensors work as well as steering controls
BTW if Alpine is like JVC it may take some time for the HU to recognise the steering c... Posted by on 22 August 2007 | Relevance: 0.6
...
Reverse sensor sound - Zilch
Steering wheel controls - Zilch
What could have happened? Should I have activated something via Lexia? Because... Posted by on 11 May 2010 | Relevance: 0.6
I have fitted my 08 plate with a Kenwood. I have rear sensors and stearing wheel controls all working great.
i use the Connects2 kits. Posted by on 11 May 2010 | Relevance: 0.6
Hi Nozza
Good to hear it.
I had a slight problem with my Kenwood install the other day, same issue as you (clock and system menu control wor... Posted by Commodore on 13 November 2011 | Relevance: 0.6
...up so no separate steering controls interface.
The speed, park cables are for hooking up certain nav units that require speed pulse etc. Posted by wozza on 07 December 2012 | Relevance: 0.6
Yes you're right wozza, the 3 extra cables I left disconnected, and the steering controls and reversing sensor work without them. I had to buy an extr... Posted by bigbruggsy on 07 December 2012 | Relevance: 0.6
... engine?
Blue wire is for the steering wheel controls. The 3.5mm plug is likely the same, but for more advanced JVC headunits (the JVC patch cabl... Posted by Commodore on 22 May 2012 | Relevance: 0.6
...roll wheel button hast to work in order for me to switch between different parameters. unfortunately the roll wheel button doesnt work and i tried dis... Posted by pars_c4 on 09 December 2011 | Relevance: 0.6
...adapter box and get both the radio steering controls and the remap for the mltifunction display controls working.
Best of luck.
Chris Posted by Commodore on 09 December 2011 | Relevance: 0.6
As part of thread: Continuous alarm
With Graphics from: Dave Forum Icons by Axialis Emotes by Seb