...speed - obviously, for each graduation on the fan control, the speed varies accordingly, so I'm not sure if i should be getting other readings than 10... Posted by trembling_blender on 21 November 2014 | Relevance: 0.6
...situation and left the new S/H fan, resistor, and control panel in the front seat.
Got a call today and they are as perplexed as me. I was told I... Posted by trembling_blender on 25 November 2014 | Relevance: 0.6
...mper cable across two of the prongs, with the fan switched on. That would have in effect 'ruled in' or 'ruled out' the resistor module as a source of ... Posted by trembling_blender on 27 November 2014 | Relevance: 0.6
...t.
I can't remember if i tried the new front control panel when this new fault started as I may have only swapped that when the original BSI faul... Posted by trembling_blender on 09 December 2014 | Relevance: 0.6
...5 minutes) engine off period, usually the climate control/blower motor works as it should be.
Sometimes after a long journey it works, sometimes not... Posted by gsa1300 on 30 August 2016 | Relevance: 0.6
...t housing has a temperature sensor on it but this controls other stuff on the engine etc, etc.
I doubt very much the thermostat is electrically c... Posted by Claude on 19 January 2018 | Relevance: 0.6
?? the diagrams for Climate Control or Manual systems are in the archive: http://c4owners.org/download.php?list.31 Posted by Dave_Retired. on 29 November 2015 | Relevance: 0.6
Sounds like a resistor has gone in the control unit (the front plate) http://c4owners.org/plugins/forum/forum_viewtopic.php?105613.post Posted by Dave_Retired. on 04 August 2012 | Relevance: 0.6
...it by the fan near the glove box? Or is it in the control panel itself? What sort/type of resistor is it? There was mention to leave it set a 21oC for... Posted by okeydokey on 11 August 2012 | Relevance: 0.6
Right, since a second control panel didn`t solve my problem, I`m now trying the £10 fix (well now £12) and have removed the drivers side heater flap... Posted by okeydokey on 17 August 2012 | Relevance: 0.6
No idea what's causing the issue, maybe a control unit or temperature sensor fault but for the fuse try F4 10 amp in the glovebox fuse board, but you ... Posted by Dave_Retired. on 14 March 2014 | Relevance: 0.6
... shows power, light and display on the heating/ac control panel??
If it does i think it need a code reader maybe?
There should be a resistor w... Posted by Farmerguy on 20 May 2022 | Relevance: 0.6
If the heating display lights up, i surprise it's similar to the C4 Grand Picasso, the control unit gets power, you did check all the fuses? In the BS... Posted by Farmerguy on 20 May 2022 | Relevance: 0.6
...Anyone looked in the documents and see if the BSI control the heating?
First i would measure if it has a ground, then if it is getting power.
... Posted by Farmerguy on 24 May 2022 | Relevance: 0.6
...imeter obviously decreases as per turning heater controls....
Connected to lexia which showed fault code as per pictures
Any ideas ppl
Ag... Posted by Rizwan on 25 May 2022 | Relevance: 0.6
...stor control module is not located on the fan, this would have been my next place to test, but as such didn't need to, haven't found it yet
Posted by Rusky68 on 26 June 2020 | Relevance: 0.6
...ponents to check,
Tempted to direct feed blower 12v via inline 30amp fuse and rated cable and switch ,not sure if could cause future problems Posted by Sam117 on 21 January 2022 | Relevance: 0.6
...u increase the blower speed through the dashboard control. If not then suggests that the resistor pack is not compatible.
Separate question - how f... Posted by Fishingc4Cat on 27 October 2024 | Relevance: 0.6
...u increase the blower speed through the dashboard control. https://kobilabs.com/civil-3d/ If not then suggests that the resistor pack is not compatibl... Posted by Nickbrown123 on 14 July 2025 | Relevance: 0.6
As part of thread: Heater motor not working please help.
With Graphics from: Dave Forum Icons by Axialis Emotes by Seb