I trust you have had a look at C6 Dave's link and the two wires I think we talking about to the micro-switch are grey and brown. I have had a look on ... Posted by DavidC4 on 05 April 2012 | Relevance: 0.6
...blue jumper wire from the 3rd contact on the microswitch back to the main earth pin on the socket.
The microswitch burnt out (blw a hole in the s... Posted by gmerry on 05 April 2012 | Relevance: 0.6
Is your 7 pin socket an OEM variety? I'm guessing you may have an after market part with two terminals on the switch. The OEM 7 pin socket micro-switc... Posted by DavidC4 on 05 April 2012 | Relevance: 0.6
... £139.30 plus VAT
6580JE "ANC CONTROL BOX" £287.59 plus VAT
Total = £426.89 plus VAT.
Which is around $720 Aussie. :-( Posted by BigJohnD on 25 June 2013 | Relevance: 0.6
Hi Jo,
Have you got a mate with a code reader? The fault you describe is similar to one I had, I looked at the brake switch but when I read the c... Posted by KenC on 04 April 2017 | Relevance: 0.6
...ulating flow insufficient detected
Manufacturer Control
My research then updated the above to ;-
7E8 - Used by engine ECU
7E9 - Trans EC... Posted by Jo10000_6 on 06 May 2017 | Relevance: 0.6
You do say that the fault is not there initially but throws up the warning after a few seconds, try starting, wait for warning, switch back to ignitio... Posted by KenC on 11 May 2017 | Relevance: 0.6
7e9 - a/t
Exhaust gas recirculating flow insufficient detected
Manufacturer Control
Copied from your post!
I got one from eBay for £35. Do... Posted by KenC on 16 May 2017 | Relevance: 0.6
...59 - MANUFACTURER SPECIFIC CODE
P0490 - EGR "A" CONTROL CIRCUIT HIGH
P0409 - EGR SENSOR "A" CIRCUIT
I've looked at the fault codes on here - ... Posted by Jo10000_6 on 26 May 2017 | Relevance: 0.6
Have you managed to get this issue resolved?
We had an almost identical problem on a C4P.
Changed the foot brake switch and checked the potentiome... Posted by Expertbeginner on 17 June 2017 | Relevance: 0.6
... ABS ECU. Error can be caused by faulty handbrake switch, or brake pedal switch. Those trigger ABS/ESP/handbrake fault. You need better diagnostic too... Posted by Ap0qalypto on 09 March 2025 | Relevance: 0.6
agree diagnosis with better tools should show this up. However considering you can get a new non oem handbrake switch for less that 15 GBP and next da... Posted by ChrisChris80 on 10 March 2025 | Relevance: 0.6
Many thanks for your posts. Am I correct in assuming this switch is also causing the front sidelights to be on permanently? Posted by Valers on 10 March 2025 | Relevance: 0.6
So, to update, took it back to Citroen who called in a "Master Technician" who diagnosed the fault as a faulty Gear Control Lever. Replaced said lever... Posted by healeddoughnut on 23 September 2020 | Relevance: 0.6
What did you use to read those error codes?
"P0700 is a generic OBD-II code that is indicating a fault within the transmission control system." ... Posted by BigJohnD on 02 March 2019 | Relevance: 0.6
I think the second error code is P1351, not P1315.
"P1351: Pre/Post heating relay circuit. Relay not controlled and glow plugs supplied. Check t... Posted by BigJohnD on 04 March 2019 | Relevance: 0.6
...was a Fleet car belonging to a council and has nothing but Citroen service history of course not ruling out the BPP switch. Just stumped ATM.
Posted by polestarboy on 11 August 2015 | Relevance: 0.6
...
Checked for power to the differential pressure switch, and it has power and ground is good.
Pulled the pre DPF pipe off the differential press... Posted by AlwaysPondering on 08 July 2021 | Relevance: 0.6
OK, so the DPF sensor woks on pulling or pushing a diaphram switch via the pipes upstream and downstream of the DPF.The more it moves the diaphram in ... Posted by GPGeorge on 10 July 2021 | Relevance: 0.6
As part of thread: Faulty Micro-Switch on 13 Pin Socket
With Graphics from: Dave Forum Icons by Axialis Emotes by Seb