...cs"...
BTW, I located new blower control module. Probably will buy it, plug and pray that fault will not occur again. Otherwise...
BR Posted by rafiki on 05 June 2014 | Relevance: 0.6
...ng and jumped 12 volts and it spins. Took off the control module and cleaned the alloy part as it was a little corroded. Incidentally the control modu... Posted by Barose on 11 June 2014 | Relevance: 0.6
...th a wire brush the corroded alloy surface of the control module. Maybe in 2 weeks it will be off again like yours.
I think your point about the ... Posted by Barose on 11 June 2014 | Relevance: 0.6
That's great! Hopefully you'll be more lucky than I was :)
My control module heat sink was also corroded up to some point. Probably I had water ... Posted by rafiki on 11 June 2014 | Relevance: 0.6
...hing worked.
After 5 - 10 minutes drive, blower control module become very hot, I could barely touch it. To avoid overheating or even fire, I turned... Posted by rafiki on 20 June 2014 | Relevance: 0.6
... one which may already be a dud. BTW, there is a control module/resistor which screws onto the side of the fan...If that's the problem rather than th... Posted by alfsgc4p on 18 March 2015 | Relevance: 0.6
... flaps not directing (maybe stuck or broken) or a controller not telling them to. Does that make sense? So it looks like I'll be delving under the d... Posted by Dilbert75 on 08 September 2015 | Relevance: 0.6
...he pair of wires (grey connector) coming into the control module. The small connector reads between 0V - 4V. Having cleaned the gutter drains and the ... Posted by paragp on 30 September 2015 | Relevance: 0.6
...he pair of wires (grey connector) coming into the control module. The small connector reads between 0V - 4V. Having cleaned the gutter drains and the ... Posted by paragp on 03 October 2015 | Relevance: 0.6
Hi, I had similar problem, when everything looked fine, but fan was not working. At the end, problem was solved by installation of new blower control ... Posted by rafiki on 03 October 2015 | Relevance: 0.6
Thank you rafiki, Fan seems to move fine, i have tried to clean the cooling fins and no luck there. Seems like i will need to buy a blower control mod... Posted by paragp on 03 October 2015 | Relevance: 0.6
Hello guys. An update. So I have not yet ordered a new blower control module. I just checked the electrics again and I am a bit confused now. There is... Posted by paragp on 10 October 2015 | Relevance: 0.6
...e from the vents. What I did was push the air con control buttons at random order until at one point the flaps moved down below and air began to flow ... Posted by Kiwicake on 15 October 2015 | Relevance: 0.6
...e from the vents. What I did was push the air con control buttons at random order until at one point the flaps moved down below and air began to flow ... Posted by paragp on 15 October 2015 | Relevance: 0.6
Same story here, Voltage at all the plugs and with 12V direct to the motor it spins fine. Installed a new control module this morning but it didn't ma... Posted by alindsay81 on 19 October 2015 | Relevance: 0.6
... 12v directly applied and it spins
2. New speed controller/resistor fitted
3. 12v measured at the connector supplying the speed controller
4. 12... Posted by alindsay81 on 26 October 2015 | Relevance: 0.6
I also had the fan stop working last week, (mines a 58 plate 1.6HDI exclusive with the digital aircon controls) Fault being traced to the "resistor pa... Posted by PeteAttryde on 07 March 2016 | Relevance: 0.6
...n fit DRL LEDs, but it'll not be a simple fit and switch on.
The chances are your car doesn't have any of the fittings, sockets, wiring, relays, ... Posted by BigJohnD on 14 October 2011 | Relevance: 0.6
Mine actually has the original sidelights in place, but they do nothing at all!!!
Can switch off the DRLs from the Personalisation Menu?
If ... Posted by BigJohnD on 14 October 2011 | Relevance: 0.6
Mine actually has the original sidelights in place, but they do nothing at all!!!
Can switch off the DRLs from the Personalisation Menu?
... Posted by routemaster1 on 14 October 2011 | Relevance: 0.6
As part of thread: C4GP Front heater/blower fan stopped working
With Graphics from: Dave Forum Icons by Axialis Emotes by Seb